로우로더 반트레일러DINKEL
4-Achs-Jumbotieflader - doppelte Rampen
로우로더 반트레일러
DINKEL
4-Achs-Jumbotieflader - doppelte Rampen
상태
신규
위치
Essen 

기본 정보
가격 및 위치
- 판매자 위치:
- Heegstraße 6-8, 45356 Essen, 독일

전화하기
기술 세부 사항
치수 및 중량
총중량:
58,000 kg
최대 적재 중량:
45,250 kg
차축 및 바퀴
차축 구성:
3축
안전 기능
ABS
제안 세부 정보
- 광고 ID:
- A22784380
- 참조 번호:
- 37868
- 업데이트:
- 마지막 업데이트: 19.09.2026
설명
You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. The following is an excerpt of the equipment. Complete equipment details are available upon request.
Chassis, gooseneck: Special steel frame made of high-strength fine-grained steels, electrically welded at the connection points, well-dimensioned outer frame. 4-axle arrangement. Wheel arches above the axles with spray mist suppression. All steel parts are sandblasted. Lateral impact protection made of anodized aluminum installed. Increased point load of approximately 30,000 kg over approximately 4,000 mm. Special design in the gooseneck area for maximum low-bed length in combination with AluLeg support legs instead of telescopic support winches, maximum rear swivel radius of the tractor unit approximately 2,100 mm. Special superstructure with rear beam widening: DINKEL – special superstructure. Self-supporting aluminum roof beam/profile approximately 120 x 100 mm, sliding cover with plastic flaps. Rear beams can be widened to approximately 4,200 mm (only for loading and unloading). Three sliding beams per side with rubber strap relief. Additional center beam locking mechanisms in the roof beam and parking position, using a pull cable and spring latch. DINKEL – lifting roof mechanically height-adjustable. Lifting roof height approximately 400 mm, operable on both or one side, without opening the opposite side and the doors. Additional height adjustment of approximately 480 mm in approximately 40 mm increments with height adjustment in the beams. Front overhang on the front wall for operation under a tarpaulin up to a total height of approximately 4,400 mm. Four rows of stackable approximately 150 mm aluminum slats on the sides, with 450 mm pockets at the bottom and 4 rows of single pockets above. In the upper bed, only 3 rows of insertable slats. Spacing between slats evenly distributed. Floor: Approximately 27 mm special water-resistant glued beech plywood, rough surface. Steel sheet in the wheel arch area. Forklift drivable according to DIN standard. Outer frame flush with the surface. Brakes: WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve). Spring-loaded brake cylinders as parking brake. Wabco Smart Board with odometer and unit load indicator. Includes WABCO tire pressure monitoring system. Axles: 4 x 10,000 kg SAF/Sauer with drum brakes in low-bed design. Air suspension with lifting and lowering device, total lift approximately 230 mm. Third and fourth axles as friction-jointed trailing axles with electrical and mechanical lock. Twin tires: 235/75 R 17.5, -16-ply. Manufacturer of our choice, including E-wheel holder. Without E-wheel. Lighting: according to EC standard including side lights in LED design. Position lights in LED design. 2 additional reversing lights. 2 work lights on the front wall inside, at the top. Painting: Chassis and superstructure in a single color in the RAL color of your choice. Center beams, axles coated with KTL (cathodic electrodeposition) in black. Corner beams in hot-dip galvanized design. Plastic parts in black. Hot-dip galvanized parts unpainted. Rims in factory silver. Special equipment included: - E-supply cable 15-pin - Air suspension in ECAS design, operated on the semi-trailer - Overwidth signage at the front and rear in zinc-plated, continuously telescopic design with attached boundary lights including so
Itodoz Dmn Rspfx Ak Asp
이 광고는 자동으로 번역되었습니다. 번역 오류가 있을 수 있습니다.
Chassis, gooseneck: Special steel frame made of high-strength fine-grained steels, electrically welded at the connection points, well-dimensioned outer frame. 4-axle arrangement. Wheel arches above the axles with spray mist suppression. All steel parts are sandblasted. Lateral impact protection made of anodized aluminum installed. Increased point load of approximately 30,000 kg over approximately 4,000 mm. Special design in the gooseneck area for maximum low-bed length in combination with AluLeg support legs instead of telescopic support winches, maximum rear swivel radius of the tractor unit approximately 2,100 mm. Special superstructure with rear beam widening: DINKEL – special superstructure. Self-supporting aluminum roof beam/profile approximately 120 x 100 mm, sliding cover with plastic flaps. Rear beams can be widened to approximately 4,200 mm (only for loading and unloading). Three sliding beams per side with rubber strap relief. Additional center beam locking mechanisms in the roof beam and parking position, using a pull cable and spring latch. DINKEL – lifting roof mechanically height-adjustable. Lifting roof height approximately 400 mm, operable on both or one side, without opening the opposite side and the doors. Additional height adjustment of approximately 480 mm in approximately 40 mm increments with height adjustment in the beams. Front overhang on the front wall for operation under a tarpaulin up to a total height of approximately 4,400 mm. Four rows of stackable approximately 150 mm aluminum slats on the sides, with 450 mm pockets at the bottom and 4 rows of single pockets above. In the upper bed, only 3 rows of insertable slats. Spacing between slats evenly distributed. Floor: Approximately 27 mm special water-resistant glued beech plywood, rough surface. Steel sheet in the wheel arch area. Forklift drivable according to DIN standard. Outer frame flush with the surface. Brakes: WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve). Spring-loaded brake cylinders as parking brake. Wabco Smart Board with odometer and unit load indicator. Includes WABCO tire pressure monitoring system. Axles: 4 x 10,000 kg SAF/Sauer with drum brakes in low-bed design. Air suspension with lifting and lowering device, total lift approximately 230 mm. Third and fourth axles as friction-jointed trailing axles with electrical and mechanical lock. Twin tires: 235/75 R 17.5, -16-ply. Manufacturer of our choice, including E-wheel holder. Without E-wheel. Lighting: according to EC standard including side lights in LED design. Position lights in LED design. 2 additional reversing lights. 2 work lights on the front wall inside, at the top. Painting: Chassis and superstructure in a single color in the RAL color of your choice. Center beams, axles coated with KTL (cathodic electrodeposition) in black. Corner beams in hot-dip galvanized design. Plastic parts in black. Hot-dip galvanized parts unpainted. Rims in factory silver. Special equipment included: - E-supply cable 15-pin - Air suspension in ECAS design, operated on the semi-trailer - Overwidth signage at the front and rear in zinc-plated, continuously telescopic design with attached boundary lights including so
Itodoz Dmn Rspfx Ak Asp
이 광고는 자동으로 번역되었습니다. 번역 오류가 있을 수 있습니다.
공급자
참고: 무료로 등록하거나 로그인하세요, 모든 정보를 확인할 수 있습니다.
등록일: 2003
58 온라인 광고
문의 보내기
전화기 & 팩스
+49 201 8... 광고
이 광고들도 당신에게 관심이 있을 수 있습니다.
성공
귀하의 메시지가 전송되었습니다.
소형 광고
Essen
8,730 km
로우로더 반트레일러
DINKEL4-Achs-Jumbotieflader - doppelte Rampen
DINKEL4-Achs-Jumbotieflader - doppelte Rampen
귀하의 광고가 성공적으로 삭제되었습니다
오류가 발생했습니다























