방수포가 설치된 오픈 세미트레일러

FLIEGL SVS 550 Spezial

The images shown are archive photos; the vehicle may still be in use!

Jumbo Low Loader Chassis for construction machinery transport up to 36,000 kg and a maximum external machine width of 2,500 mm. Fifth wheel plate with replaceable 2" king pin. Rear slope approximately 1,500 mm long at 7°. Ramp shaft closed at top with steel/checker plate.

Trailer B-dimension: 12,000 mm
Free rear swing radius approx.: 2,350 mm
Spare wheel carrier with 1 spare wheel
Plastic toolbox
In the low-bed: Omega rail laterally below the outer frame as a lashing bar for tarpaulin and spacer holders for lashing pins, not within the wheel area.

Lashing Points:
Gooseneck:
- 5 pairs of lashing points recessed in outer frame, each rated at 5 t
- 2 pairs of lashing pins recessed on top and side of outer frame, each rated at 10 t
Low-bed:
- 7 pairs of lashing pins recessed on top and side of outer frame, each rated at 10 t
- 9 pairs of lashing points recessed in outer frame, each rated at 5 t
- 3 pairs of additional folding lashing points recessed in the low-bed floor, each 10 t (1x before the drop, 1x in front of the 1st axle, 1x behind the 3rd axle)

Axles & Suspension:
- Drum brake axles
- Last 2 axles self-steering
- Air suspension with lift & lower valve + auto-reset function
- Raise & lower function with quick release

Wheels and Tires:
- 205 / 65 R 17.5 for 8,000 kg axle load technical max. at 90 km/h
- Steel rims twin arrangement

Brake System:
- 2-line air brake system
- Spring-loaded parking brake
- 2 non-interchangeable coupling heads at front, without connecting line
- Knorr EBS

Electrics:
- 2 pairs of double LED warning panels, extendable
- 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at front
- 24 Volt, multi-chamber LED lights
- Flashing side marker lights
- Beacon with holder
- Interior LED work light on front wall
- 2 additional LED work lights at rear, switched via reversing light

Floor:
- Floor designed for maximum forklift axle load of 10,000 kg at minimum 300 mm tire width (note: deformation possible!)

Stakes:
- 3 pairs of sliding stakes, movable along entire length, with four insert sockets each; only the rear 2 zones are of equal length!
- Stake positions: 1x gooseneck, 3x in low-bed

Insert Slats:
Nwodpfx Aoylkywjh Djc
- 5 rows of wooden insert slats

Access Ramps:
- Ramp surface with "Mega Grip" serrated grating (max. forklift axle load 9,000 kg at min. 200 mm tire width)
- Hydraulically operated via independent electric unit installed in stainless steel box front-right, including ramp control; additional operation via radio remote control incl. rear support operation, customer's responsibility! NATO socket on truck required, including connecting line to truck as spiral cable; connection line must NOT be connected while driving! Truck not included.
- Steel ramp full width, approx. 3,300 mm long + 3-part aluminium foldable section approx. 900 mm for total ramp length 4,100 mm; if necessary, additional phenolic board max. 9 mm thick under aluminium sections for reduced ramp angle; ramp load capacity 26,000 kg, heavy-duty version; over ramp shaft steel/checker plate; ramp secured during transit with top link.

Exact specification available on request!

이 광고는 자동으로 번역되었습니다. 번역 오류가 있을 수 있습니다.